Jan David-Andersen

14/09/2015
14:58
Admin

 

 

 

Jan David-Andersen is a true engine enthusiast.  After he stopped making engines for sale, he continued to make engines for his own use.  Here he shows one of his recent creations.

 

 

 

 

 

 

 

 
     

 

Text and photos: Gunnar Kock 

Attempts at translations: Arvid Martinussen

Jan David-Andersen was making model aircraft engines from 1950 to 1964. We here show most of the engine models his company "David-Andersen Engine" produced. Note that David-Andersen did not use the variant designations of his engines. Version number is used here to keep order. The engines were handicrafts. It was possible to make changes from one engine to another, and it was done. Version numbers in a program is therefore referring only to major changes, but in between there were many small ones. Our collection is on display at Norwegian Aviation Museum.

 

 

 

 

 

 

 

 

 

    

 

 David Andersen 2.5 cc version 1.
"The eccentric" was produced in 170 copies in 1950, and David-Andersen's first mass-produced engine. The crankshaft runs in a bearing with an eccentric hole for the crankshaft. The lever on the side of the motor is connected to the bearing. By turning the handle, the crankshaft is lifted or lowered in relation to the cylinder, and thus adjusts the compression.

The Swedish master builder Arne Hende made in the nineties a series of 50 copies of this engine.

According to David Andersen the copies are nicer built than the originals. "

A picture of a copy to the left

 

 

   

 

The "Exhaust pipe engine" is a further development of the "eccentric". The engine has a counter piston at the top of the cylinder and is provided with a compression screw on top of the cylinder head. The front piece of the crankcase is of a new design, making suction of air/fuel mixture through the crankshaft possible.

 

 

 

 

David Andersen 2.5 cc version 2.
The crankcase is modified by removing the suction pipe at the back. In this and all subsequent versions of “The exhaust pipe engine” one can see a circular extent where the suction pipe was located. Like its predecessor, the cylinder and fins are made from a piece of cast iron. On earlier versions the rear of the crankcase was flat. Later editions have a round DA mark and an elevated area for serial number - but not all had the serial numbers. It was not uncommon for owners to remove the exhaust pipes. The engine was produced from 1950 to 1954.

On some drawings with English measurements the engine is termed as DA 2.46 cc.

 

 

   

 

D-A 2.5 cc, version 3 (fins on the head)

Version 3, which came in 1954, has separate heat sinks in machined aluminum with milled cooling fins on top - much like the motorcycle engines from those days. Later editions have a suction pipe in machined aluminum, improved cylinder construction and slightly better performance.

 

 

   

 

 

 

D-A 2.5 cc, version 3 (plain head)

The last “Exaust pipe engines” had a plain cylinder head, no cooling fins. On the back of crankcase can be read "MADE IN NORWAY" in addition to the DA company label. The straight sides of the engine mounting lugs are not original. Here the owner has used a file. "The plain head" was made in small numbers around 1956 – 57.

 

 

 

 

 

 

 

 

 

 

 

 

D-A 2.5 cc, version 3, boat engines

David-Andersen made boating equipment for his engines. Cooling jacket for water cooling is found in several variants. Note that the flywheel was set right on the cone of the crankshaft and replaced the trust washer.

The flywheel in the picture is not original. This engine comes from Nils Boye and has a Webra R / C nozzle that he has put on.

 

 

   

 

 

 

  

D-A 2.5 cc, Seen from the rear.

The first engines were completely plane at the rear of the crankcase. Eventually each motor got an elevated number area and the D-A company label, and the last years also "MADE IN NORWAY"  could be seen at the back of the crankcase.

Note the circular extent seen in the middle of the engine just below the exhaust manifold. In earlier versions this was the location of the suction pipe.

 

 

 

 

 

 

 

 

 

David-Andersen Drabant 25

The Drabant was David-Andersen's first modern high performance engine. It had two ball bearings and cylinder volume of 2.5 cc. Version 1 came in 1957 and replaced "The exhaust pipe engine".

 

 

 

 



It came with 2 or 4 exhaust ports. This model introduced a lock nut at the compression screw, and thus solved the problem of "comp screw" shaking loose. This solution was used for all subsequent D-A engines.

D-A Drabant 25, version 1, "SKF bearings"

Version 1 is easily recognized because the propellers are attached with a bolt that goes into the crankshaft. The bolt head is shaped like a small spinner. The bearings are SKF. It had a crankshaft with a diameter of 8.00 mm. It was too small. Therefore, it did not take long after the engines were relased, until they began to flow back to the shop with broken cranks.

It soon became clear that improvements were needed, and the engine was not produced in large numbers any longer.

David-Andersen delivered on request a tuned version of the engine with guaranteed max. revolutions.

 

 

   

 

 

 

 

 

 

D-A Drabant 25, version 2
In version 2 the diameter of the crankshaft were increased to 3/8 "(9.53 mm). It  proved to be strong enough. The bearings are from Hoffmann and the propellers are attached with a special nut. This motor type is the most produced of all D-A engines. It could like the Tellus and Satellite be fitted with exhaust pipes. See photo of the Satellite.
In the U.S., Drabant was marketed as "DA 15", 15 by the cylinder volume in hundredths of cubic inches.

   

 

 

 

 

 

 

D-A Drabant 25, R / C motor

Drabant R / C is a regular version 2 except for the Webra carb. The engine is not mend to be throttled, but designed to run at max revs in a free flight model or to be used in line controlled planes, like all the other D-A engines.

The engine in the picture has a David-Andersen special-spinner.

   

 

 

 

 

 

  

D-A Drabant 25 version 3
Version 3 Jan David-Andersen made some years ago for his own enjoyment. He only made a small number.
The engine has a suction pipe, inspired by Oliver Tiger, and a set screw for locking the compression screw, located at  the side of the cylinder head, similar to the Irvine.

 

   

 

   

Drabant med 1 eksosport

 

 

Drabant with just one exhaust port.

D-A was always trying to come up with better solutions. This engine is a good example, where he has experimented with just one exhaust port. The engine has no serial number. A collector has bought it from England.

 

 

 

 

 

 

 

 

 

 

 

 

D-A Tellus 25
Tellus is the last of David-Andersen 2.5 cc engines. The engine is mostly made from Drabant parts, but has no ball bearings, and is therefore  not so powerful, but it was cheaper in production. Only the crankcase and the crankshaft separates it from the Drabant. The engine came both with shiny or colored (anodized) heat sinks. As with all David-Andersen engines bearings are not equipped with bronze liners. David-Andersen had looked to British cars, and came to the conclusion that aluminum is a good bearing material for steel.

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D-A 1 cc, version 1 "Screw on cylinder"
DA 1 cc was the second type of engine developed by David-Andersen. It came in 1954 and was a typical engine of its time. The cylinder with cooling fins and no separate cylinder head, was screwed into the crankcase, keeping the cylinder and thr crankcase together. The construction was not entirely successful. The workshop did not have good quality equipment to make the threads. The users of the engines were often brutal when removing the cylinder. Many engines were damaged during disassembly.
Some engines had, as the engine to the right, suction pipe in machined aluminum.

 

 

   

 

 

To cure the problems with version 1, the engine was modified.  It was constructed with new cooling fins which were fastened with two screws. The crankcase was modified with lugs for the screws.  The cylinder was also modified.  In some manuals a drawing of this engine is mention as “Satellitt”. 

 

 

   

 

 

 

 

 

  D-A Satellite 10

D-A Satellite 10
Satellite is a further development of the 1 cc, version 2. It is a rugged and powerful little engine with plain bearings - customized for young rough users. The model was available in 1958.
The engine to the left is blown with dust from walnut and polished, nice but historically incorrect.
The engine to the right has exhaust pipes. The exhaust pipes for the Drabant and the Tellus looked the same.
Note the differences in the fins.

 

 

   

 

 

 

D-A ”The Shumann engine.”

As a student at Stockholm Tech. Jan David-Andersen designed engines which his friend and mentor Shumann in Oslo produced in limited numbers.  This is one of them.  Shumann worked as a mechanic in the workshop of Jan’s father. The engine is owned by relatives of Shumann, and is called "The Shumann-engine."

 

   

 Selvbyggermotor fra David Andersen

 

 

Hi, here I would like to contribute a photo of a David-Andersen "Self-build engine" which you can post. It helps to fill out the story of D-A model engines. Best regards, Jens Eirik Skogstad

Thank you very much for the contribution!

Arvid M

David Andersen's "Self Build Engine".

A nice example of a D-A self build engine.

Here is a supplement to the picture Skogstad sent us of the David-Andersen “home-built engine”.
The engine was built by the master builder Les Stone.  The picture is taken from www.modelenginenews.org.

 

 

 

 

  

David-Andersen, Self Build engine
This engine is constructed by Jan David-Andersen in 1944, and he published blueprints and building instructions in the book "Diesel engines for model aircraft, boats and cars" which he released on his own book publisher in January 1945.
During and after the www2 it was no model airplane engines to buy, so the one and only option to get an engine was to build it yourself if you had the right tools.
Bore is 13 mm and stroke of 18 mm. It gives a displacement of 2.39 cc

   

 

 

 

 

 

 

 

 

The Bramek engine.

Bramek 1.5 cc is a less known motor. It was produced by Arvid Brambani and Trygve Gilhoff in the years 1953-1955. They made a little more than 100 engines, mostly for their own pleasure. Gilhoff had a small fine mechanical workshop at Bygdøy in Oslo.
The crankcase was painted with blue anthracite. On the bottom of the crankcase it says "Bramek" and serial number.
The engines were mainly sold through EEO, Model Hobby and Ingwald Nilsen in Oslo